●Z軸自動進刀，採NC伺服系統，控制AC伺服馬達，可穩定、快速、精確的控制進刀。
●

觸控式面版，集中操控，配合螢幕顯示器，所設定的功能、數值、研磨作業執行實況、立即顯示。並可當精密光學尺使用，操控簡單、準確，進而提高生產效率。

●自動進刀功能多重選擇：
  1. 平面研磨進刀
  2. 單面切溝研磨進刀
  3. 雙面切溝研磨進刀
●自動進刀量功能多重選擇：
  1. 粗磨進刀量 0.002mm-0.15mm，數次1-99次
  2. 精模進刀量 0.002mm-0.02mm，數次1-10次
  3. 零研魔數次 0-5次，砂輪可設定自動上昇
●快速進給功能多重選擇：
  1. 快速昇降
  2. 慢速昇降
  3. 寸動昇降

●微調進給功能：採電子式手動操控 微調進給每次最小進刀量 0.002mm。
●安全裝置功能：
  1. 自動進刀研磨執行中，快速下降進給功能失效。
  2. 切溝研磨進刀執行中，前後進給功能失效。
  3. 砂輪馬達過負載，砂輪立即自動上昇。
● Automatic tool feeding for Axis-Z, adopting a NC servo system to control AC servo motor, thus ensuring stable,fast, and precisio feeding control.
● Touch panel design and central controlling. This, together with the monitor, displays the seting functions, digitals, and real grinding situations immediately.
●Multi-selections for automatic tool feeding functions:
  1. surface grinding
  2. single face cutting
  3. double face cutting
●Multi-selections for automatic feeding volumes:
  1. rough fool feeding volume:0.002mm~0.15mm,1-99 times
  2. fine tool feeding volume:0.002mm-0.02mm,1-10 times
  3. zero grinding:0-5times, sanding wheel automatic arising is available
●Multi-selections for fast tool feeding functions.
  1. fast arising/descending
  2. slow arising/descending
  3. arising/descending by inch.
● Micro-adjusting tool feeding functions:Electronics-type manual controlled, with minimum feeding volume reaching 0.002mm Safety device functions:
  1. invalid fast decending during automatic tool grinding
  2. invalid forward/backward function during cutting
  3. sanding wheel automatically arises in case of overloading motor
1. 先按 Z 軸 ON ，再按螢幕 ON ，完成開機作業。
2. 尺寸、數次、設定程序：按設定鍵，依指示設定，按數字後，再按確認鍵，即可輸入，完成設定按完成設定鍵。（重新設定時，按設定鍵，即可重新設定）。
3. 以上完成設定後，再選擇平面研磨、單面切溝、雙面切溝等功能進行研磨作業。
4. 研磨作業執行中，快速上升、下降、微調等功能失效。
5.
快速下降時，需先按 鍵，才能進行下降功能，快速下降功能不用時，請即時按停止鍵，以免發生危險。
6.
按座標歸零，螢幕中英文轉換 ，一直按住到轉換為止。（須等幾秒鐘）
7. 螢幕保護裝置：不作業時，幾分鐘後螢幕字幕自動消失，使用時再按螢幕 ON鍵，即可恢復。
8. 為保護控制線路正常操作，電源線接上時，砂輪必須正轉，若砂輪反轉時，必須換電源線相，不可換砂輪馬達線相。油壓馬達、冷卻馬達，依指示方向接線（可換馬達線相）
1. Press Z-axis button ON and screen ON to get started of operation.
2. Size/Counting Setting: Press the setting key and follow the setting instruction; after keying in the number, press the confirm key for the completion of the setting. (Press the resetting key for the resetting purpose.)
3. When finished the above setting, select the function key for surface grinding and or single/double face grinding.
4. During the grinding operation, the functions for micro-adjustments such as rapid escalation and descending are in valid.
5.
Press the button for rapid descending. Press the stop button to avoid danger after the descending
function is completed.
6.
Press the button for the coordinate function. (Few seconds are waited.)
7. Screen protection device: The screen will turn off automatically in few minutes after the operation ceases. Press the screen button ON to resume operation.
8. In order to protection the normal operation, the dressing wheel must be operated in clockwise if the power line is on. When the wheel is operated in counterclockwise, the power line box, rather than the motor box, has to be changed. Both hydraulic and cooling motors are connected as instructions followed. (Motor line box is changeable.)